Affichage des résultats 1 à 6 sur 6
  1. #1
    Date d'inscription
    novembre 2013
    Messages
    22
    Thanks
    0
    Total, Thanks 25 fois
    Pouvoir de réputation
    0

    Impossible de récupérer mon prismcube même avec tera term ?

    Bonjour a tous,

    Apres avoir complètement plantée mon prismcube, j'ai trouver un tuto sur comment récupérer un prismcube avec le logiciel Tera Term et un cable null modem après un plantage; trouver ici:
    **Contenu caché: Cliquez sur Thanks pour afficher. **

    Je rencontre juste un problème a la dernière etapes, quand je veux envoyer: u-boot.bin , l'ecran noir de tera term indique en derniere ligne : up_parent +0x0/0x18
    Ma cle usb brancher sur le port usb de la prismcube contient l'image Emergency Update image
    l'ecran du prismcube indique "UPDATE" et une lampe clignote rouge sur la face avant
    Mais jamais même apres 10 minutes "REMOVE USB" ??


    Quelqu'un peut il m'aider svp
    Merci
    Dernière modification par Mimiche ; 09/04/2015 à 09h51. Motif: Lien non caché

  2. # ADS
    Ich'har Circuit publicitaire
    Date d'inscription
    Toujours
    Messages
    Plusieurs
     
  3. #2
    Date d'inscription
    juillet 2014
    Localisation
    ***********************
    Messages
    3 132
    Thanks
    2
    Total, Thanks 11 870 fois
    Pouvoir de réputation
    0

    Re : Impossible de récupérer mon prismcube même avec tera term ?

    Bonjour Warmup,

    As tu installé le Jumper avant de flasher ?
    As tu formaté ta clé usb fat32 ?
    Tu peux aussi essayer une autre clé usb.

  4. #3
    Date d'inscription
    novembre 2013
    Messages
    22
    Thanks
    0
    Total, Thanks 25 fois
    Pouvoir de réputation
    0

    Re : Impossible de récupérer mon prismcube même avec tera term ?

    Bonjour toonsi,

    Merci pour ta réponse,
    j'ai bien formater ma clé usb fat32 et aussi installer le jumper comme indiquer sur le visuel du tuto
    Je comprend pas pourquoi cela ne fonctionne pas pour moi..
    Je vais essayer une autre clé usb que je vais acheter demain matin et je tiens au courant du résultat

  5. #4
    Date d'inscription
    novembre 2013
    Messages
    22
    Thanks
    0
    Total, Thanks 25 fois
    Pouvoir de réputation
    0

    Re : Impossible de récupérer mon prismcube même avec tera term ?

    Bonjour,

    Voila j'ai acheter un nouveau cable null modem avec un usb pour aller sur mon portable plus simple.
    Apres avoir reçus le câble je recommence les même opération pour récupérer mon prismcube a l'origine plantée mais le même problème persiste.
    Voici un copie d’Écran de tera term peut être pour mieux illustrer mon problème

    þCCCCCCCC

    Starting Microloader ASM built on Jun 17 2013 20:08:40...
    Initializing PLLs...
    Initializing Clocks..
    Initializing DDR PLLs/Clocks...
    Initializing DDR controller...
    Initializing data section...
    Initializing stack ptr...
    Switching to 'C' code...
    Starting Microloader C...
    Found Internal Ethernet PHY on GMAC0....
    Sampling the UART for input ...
    Input any key on UART to stop for flash download
    GCS in ISA MODE
    GCS: NAND DEVICE SETUP COMPLETE
    NAND: Initialization complete
    starting UART boot ...
    Setting up default ATAG list...
    Jumping to Uboot .........




    U-Boot 2009.08-dirty (Jun 19 2013 - 13:44:41)


    DRAM: 512 MB
    malloc: Using memory from 0x04200000 to 0x04400000
    GCS: Setup In ISA MODE
    UART Boot not Supported .....
    GCS: NAND DEVICE SETUP COMPLETE
    Boot Device: NAND Flash
    NAND: 512 MiB
    Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    In: serial
    Out: serial
    Err: serial
    Net: lip0
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... 2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    ./
    ../
    4790 checkusb.img
    61 checkusb.img.md5
    3099044 kernel.uimage
    62 kernel.uimage.md5
    27277158 ramdisk.gz
    59 ramdisk.gz.md5
    1300 ramdisk_update_script.sh
    73 ramdisk_update_script.sh.md5
    626412 u-boot.bin
    59 u-boot.bin.md5
    3022529 uimage
    55 uimage.md5
    52000 uldr.bin
    57 uldr.bin.md5
    65536 uldr.bin.uartboot_img
    56 uldr.bin.uartboot_img.md5


    16 file(s), 2 dir(s)


    reading update_ruby/checkusb.img


    4790 bytes read


    NAND erase: device 0 offset 0x17d00000, size 0x2d00000
    Erasing at 0x1a9e0000 -- 100% complete.
    OK
    Unknown command 'display_strings' - try 'help'
    Unknown command 'display_strings' - try 'help'
    Unknown command 'check_update' - try 'help'
    Unknown command 'write_vfd' - try 'help'
    Unknown command 'display_strings' - try 'help'
    Unknown command 'display_strings' - try 'help'


    NAND read: device 0 offset 0x1700000, size 0x600000
    NAND read from offset 1700000 failed -74
    6291456 bytes read: ERROR
    ## Booting kernel from Legacy Image at 04400000 ...
    Image Name: uImage
    Image Type: ARM Linux Kernel Image (gzip compressed)
    Data Size: 3097868 Bytes = 3 MB
    Load Address: 00008000
    Entry Point: 00008000
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Linux version 2.6.34 (amedeo@meohome) (gcc version 4.7.2 (GCC) ) #1 SMP Tue Mar 17 17:50:05 CET 2015
    [ 0.000000] CPU: ARMv7 Processor [411fc091] revision 1 (ARMv7), cr=10c57c7d
    [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
    [ 0.000000] Machine: NXP BL-STB platform
    [ 0.000000] ChipID=0x2 ChipRevID=0x2
    [ 0.000000] EMAC address found in ATAG list ...
    [ 0.000000] Mac 0 address bytes = 00:00:de:ad:be:f0
    [ 0.000000] Mac 1 address bytes = 00:00:de:ad:be:f1
    [ 0.000000] Memory policy: ECC disabled, Data cache writealloc
    [ 0.000000] Early platform io descriptors mapping...
    [ 0.000000] PERCPU: Embedded 7 pages/cpu @805fb000 s6816 r8192 d13664 u65536
    [ 0.000000] pcpu-alloc: s6816 r8192 d13664 u65536 alloc=16*4096
    [ 0.000000] pcpu-alloc: [0] 0
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 129536
    [ 0.000000] Kernel command line: noinitrd console=ttyS1,115200n8 mtdparts=nx_ 2017:1024k@0k(uldr),1792k@1024k(u-boot),20m@3m(configure),6m@23m(kernel),350m@29 m(root),45m@381m(update),5m@426m(uImage),35m@431m( ramdisk),-(extra) ubi.mtd=4 ro ot=ubi0:rootfs rootfstype=ubifs rw rootflags=sync ldver=4 hwver=1 videomode=PAL
    [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Memory: 256MB 256MB = 512MB total
    [ 0.000000] Memory: 323296k/323296k available, 200992k reserved, 0K highmem
    [ 0.000000] Virtual kernel memory layout:
    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
    [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
    [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
    [ 0.000000] vmalloc : 0xa0800000 - 0xd0000000 ( 760 MB)
    [ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
    [ 0.000000] modules : 0x7e800000 - 0x80000000 ( 24 MB)
    [ 0.000000] .init : 0x80008000 - 0x80030000 ( 160 kB)
    [ 0.000000] .text : 0x80030000 - 0x80574000 (5392 kB)
    [ 0.000000] .data : 0x80596000 - 0x805ccce0 ( 220 kB)
    [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N odes=1
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] NR_IRQS:388
    [ 0.000000] Initializing Cortex Interrupt Distributer (DISTR) at Vir:0xE01010 00 = Phy:0xE0101000
    [ 0.000000] Initializing Cortex Generic Interrupt Controller (GIC) at Vir:0xE 0100100 = Phy:0xE0100100
    [ 0.000000] Initializing Cortex A9 Global Timer at Vir:0xE0100200 = Phy:0xE01 00200, using Irq:27, at Freq:250000000
    [ 0.000000] Console: colour dummy device 80x30
    [ 0.000000] console [ttyS1] enabled
    [ 0.010000] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
    [ 0.280000] Mount-cache hash table entries: 512
    [ 0.280000] Initializing cgroup subsys devices
    [ 0.290000] CPU: Testing write buffer coherency: ok
    [ 0.290000] Calibrating local timer... 249.49MHz.
    [ 0.360000] L310 cache controller enabled
    [ 0.360000] l2x0: 8 ways, CACHE_ID 0x410004c4, AUX_CTRL 0x22021001, Cache siz e: 131072 B
    [ 0.370000] Brought up 1 CPUs
    [ 0.370000] SMP: Total of 1 processors activated (996.14 BogoMIPS).
    [ 0.380000] devtmpfs: initialized
    [ 0.380000] NET: Registered protocol family 16
    [ 0.390000] Adding platform devices...
    [ 0.390000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counter s available
    [ 0.400000] SATA: Adjusting los_lvl (rd_val=0x8a46, wr_val=0x8ae6)
    [ 0.410000] SATA: Adjusting rx_term_en0/1 (rd_val=0x2750275, wr_val=0x2770277 )
    [ 0.420000] bio: create slab <bio-0> at 0
    [ 0.420000] vgaarb: loaded
    [ 0.430000] SCSI subsystem initialized
    [ 0.430000] usbcore: registered new interface driver usbfs
    [ 0.440000] usbcore: registered new interface driver hub
    [ 0.440000] usbcore: registered new device driver usb
    [ 0.450000] cfg80211: Calling CRDA to update world regulatory domain
    [ 0.450000] Switching to clocksource global_timer_src
    [ 0.460000] NET: Registered protocol family 2
    [ 0.460000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.470000] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
    [ 0.480000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.480000] TCP: Hash tables configured (established 16384 bind 16384)
    [ 0.490000] TCP reno registered
    [ 0.490000] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.500000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.500000] NET: Registered protocol family 1
    [ 0.510000] RPC: Registered udp transport module.
    [ 0.510000] RPC: Registered tcp transport module.
    [ 0.520000] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.520000] PMU: registered new PMU device of type 0
    [ 0.530000] PM: Apollo power mgmt initialization.
    [ 0.540000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [ 0.550000] Registering unionfs 2.5.4 (for 2.6.34-rc0)
    [ 0.560000] JFFS2 version 2.2. (NAND) (SUMMARY) c 2001-2006 Red Hat, Inc.
    [ 0.560000] SGI XFS with security attributes, realtime, large block/inode num bers, no debug enabled
    [ 0.570000] msgmni has been set to 631
    [ 0.580000] alg: No test for stdrng (krng)
    [ 0.580000] io scheduler noop registered
    [ 0.590000] io scheduler cfq registered (default)
    [ 0.590000] nx_dmac_1902 nx_dmac_1902.1: NXP DMA Controller IP_1902 found @ [ a08ba000] (rev 41080), 8 channels
    [ 0.610000] uart-ip3106.0: ttyS0 at MMIO 0xe06e1000 (irq = 46) is a uart-ip31 06
    [ 0.620000] uart-ip3106.1: ttyS1 at MMIO 0xe06e2000 (irq = 47) is a uart-ip31 06
    [ 0.630000] uart-ip3106.2: ttyS2 at MMIO 0xe06e3000 (irq = 48) is a uart-ip31 06
    [ 0.630000] uart-ip3106.3: ttyS3 at MMIO 0xe06e4000 (irq = 49) is a uart-ip31 06
    [ 0.640000] nx_dmac: Registered with 8 channels
    [ 0.650000] brd: module loaded
    [ 0.660000] loop: module loaded
    [ 0.660000] Uniform Multi-Platform E-IDE driver
    [ 0.670000] ide-gd driver 1.18
    [ 0.670000] sata-apollo sata-apollo.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
    [ 0.680000] sata-apollo sata-apollo.0: flags: ncq sntf stag pm led clo only p mp pio slum part ccc sxs
    [ 0.690000] scsi0 : sata-apollo
    [ 0.690000] scsi1 : sata-apollo
    [ 0.690000] ata1: SATA max UDMA/133 ahci 0xa08d2000 port 0xa08d2100 irq 39
    [ 0.700000] ata2: SATA max UDMA/133 ahci 0xa08d2000 port 0xa08d2180 irq 39
    [ 0.710000] nx_2016 nx_2016: map_probe failed
    [ 0.720000] nx_2016: probe of nx_2016 failed with error -5
    [ 0.720000] ONFI flash detected
    [ 0.730000] ONFI param page 0 valid
    [ 0.730000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix H27U4G8F 2DTR-BC)
    [ 0.740000] 9 cmdlinepart partitions found on MTD device nx_2017
    [ 0.740000] Creating 9 MTD partitions on "nx_2017":
    [ 0.750000] 0x000000000000-0x000000100000 : "uldr"
    [ 0.760000] 0x000000100000-0x0000002c0000 : "u-boot"
    [ 0.760000] 0x000000300000-0x000001700000 : "configure"
    [ 0.770000] 0x000001700000-0x000001d00000 : "kernel"
    [ 0.770000] 0x000001d00000-0x000017b00000 : "root"
    [ 0.780000] 0x000017d00000-0x00001aa00000 : "update"
    [ 0.780000] 0x00001aa00000-0x00001af00000 : "uImage"
    [ 0.790000] 0x00001af00000-0x00001d200000 : "ramdisk"
    [ 0.790000] 0x00001d200000-0x000020000000 : "extra"
    [ 0.800000] UBI: attaching mtd4 to ubi0
    [ 0.800000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
    [ 0.810000] UBI: logical eraseblock size: 126976 bytes
    [ 0.820000] UBI: smallest flash I/O unit: 2048
    [ 0.820000] UBI: VID header offset: 2048 (aligned 2048)
    [ 0.830000] UBI: data offset: 4096
    [ 1.070000] ata1: SATA link down (SStatus 0 SControl 300)
    [ 1.440000] ata2: SATA link down (SStatus 0 SControl 300)
    [ 1.930000] UBI: max. sequence number: 213
    [ 1.950000] UBI: attached mtd4 to ubi0
    [ 1.950000] UBI: MTD device name: "root"
    [ 1.960000] UBI: MTD device size: 350 MiB
    [ 1.960000] UBI: number of good PEBs: 2800
    [ 1.970000] UBI: number of bad PEBs: 0
    [ 1.970000] UBI: number of corrupted PEBs: 0
    [ 1.980000] UBI: max. allowed volumes: 128
    [ 1.980000] UBI: wear-leveling threshold: 4096
    [ 1.990000] UBI: number of internal volumes: 1
    [ 1.990000] UBI: number of user volumes: 1
    [ 1.990000] UBI: available PEBs: 0
    [ 2.000000] UBI: total number of reserved PEBs: 2800
    [ 2.000000] UBI: number of PEBs reserved for bad PEB handling: 28
    [ 2.010000] UBI: max/mean erase counter: 136/63
    [ 2.010000] UBI: image sequence number: 1077297098
    [ 2.020000] Atmel at76x USB Wireless LAN Driver 0.17 loading
    [ 2.020000] usbcore: registered new interface driver at76c50x-usb
    [ 2.030000] usbcore: registered new interface driver zd1201
    [ 2.040000] GMAC:Internal PHY being used with GMAC0
    [ 2.040000] GMAC:Registering Ethernet ISR number 40
    [ 2.050000] GMAC:Ethernet interface eth0 registered
    [ 2.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 2.060000] usb-ip9028 usb-ip9028.0: IP9028 embedded EHCI USB controller
    [ 2.060000] usb-ip9028 usb-ip9028.0: new USB bus registered, assigned bus num ber 1
    [ 2.070000] UBI: background thread "ubi_bgt0d" started, PID 41
    [ 2.100000] usb-ip9028 usb-ip9028.0: irq 93, io base 0xe066c000
    [ 2.120000] usb-ip9028 usb-ip9028.0: USB 2.0 started, EHCI 1.00
    [ 2.120000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 2.130000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
    [ 2.130000] usb usb1: Product: IP9028 embedded EHCI USB controller
    [ 2.140000] usb usb1: Manufacturer: Linux 2.6.34 ehci_hcd
    [ 2.150000] usb usb1: SerialNumber: ip9028
    [ 2.150000] hub 1-0:1.0: USB hub found
    [ 2.150000] hub 1-0:1.0: 1 port detected
    [ 2.160000] usb-ip9028 usb-ip9028.1: IP9028 embedded EHCI USB controller
    [ 2.170000] usb-ip9028 usb-ip9028.1: new USB bus registered, assigned bus num ber 2
    [ 2.200000] usb-ip9028 usb-ip9028.1: irq 94, io base 0xe066d000
    [ 2.220000] usb-ip9028 usb-ip9028.1: USB 2.0 started, EHCI 1.00
    [ 2.220000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
    [ 2.230000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
    [ 2.230000] usb usb2: Product: IP9028 embedded EHCI USB controller
    [ 2.240000] usb usb2: Manufacturer: Linux 2.6.34 ehci_hcd
    [ 2.250000] usb usb2: SerialNumber: ip9028
    [ 2.250000] hub 2-0:1.0: USB hub found
    [ 2.250000] hub 2-0:1.0: 1 port detected
    [ 2.260000] usb-ip9028 usb-ip9028.2: IP9028 embedded EHCI USB controller
    [ 2.270000] usb-ip9028 usb-ip9028.2: new USB bus registered, assigned bus num ber 3
    [ 2.270000] usb-ip9028 usb-ip9028.2: irq 95, io base 0xe066e000
    [ 2.300000] usb-ip9028 usb-ip9028.2: USB 2.0 started, EHCI 0.00
    [ 2.300000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [ 2.310000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
    [ 2.310000] usb usb3: Product: IP9028 embedded EHCI USB controller
    [ 2.320000] usb usb3: Manufacturer: Linux 2.6.34 ehci_hcd
    [ 2.330000] usb usb3: SerialNumber: ip9028
    [ 2.330000] hub 3-0:1.0: USB hub found
    [ 2.330000] hub 3-0:1.0: 0 ports detected
    [ 2.340000] usbcore: registered new interface driver cdc_wdm
    [ 2.340000] usbcore: registered new interface driver libusual
    [ 2.350000] mice: PS/2 mouse device common for all mice
    [ 2.360000] rtc_apollo rtc_apollo: rtc core: registered rtc_apollo as rtc0
    [ 2.360000] i2c /dev entries driver
    [ 2.370000] sdhci: Secure Digital Host Controller Interface driver
    [ 2.370000] sdhci: Copyright(c) Pierre Ossman
    [ 2.380000] usbcore: registered new interface driver usbhid
    [ 2.380000] usbhid: USB HID core driver
    [ 2.390000] oprofile: using arm/armv7-ca9
    [ 2.390000] TCP cubic registered
    [ 2.400000] NET: Registered protocol family 17
    [ 2.400000] lib80211: common routines for IEEE802.11 drivers
    [ 2.410000] ThumbEE CPU extension supported.
    [ 2.410000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
    [ 2.420000] rtc_apollo rtc_apollo: setting system clock to 1970-01-01 00:00:0 0 UTC (0)
    [ 2.430000] UBIFS: parse sync
    [ 2.430000] UBIFS: background thread "ubifs_bgt0_0" started, PID 44
    [ 2.460000] UBIFS: recovery needed
    [ 2.560000] UBIFS: recovery completed
    [ 2.570000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)
    [ 2.570000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes : 2048 bytes/2048 bytes
    [ 2.580000] UBIFS: FS size: 350072832 bytes (333 MiB, 2757 LEBs), journal siz e 9023488 bytes (8 MiB, 72 LEBs)
    [ 2.590000] UBIFS: reserved for root: 0 bytes (0 KiB)
    [ 2.600000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID CDF246A6-2C24- 4A4D-B6CF-2EDBF9BC1037, small LPT model
    [ 2.610000] usb 2-1: new high speed USB device using usb-ip9028 and address 2
    [ 2.620000] VFS: Mounted root (ubifs filesystem) on device 0:14.
    [ 2.620000] devtmpfs: mounted
    [ 2.630000] Freeing init memory: 160K
    /sbin/init: error while loading shared libraries: libkmod.so.2: cannot open shar ed object file: No such file or directory
    [ 2.700000] Kernel panic - not syncing: Attempted to kill init!
    [ 2.700000] [<80037450>] (unwind_backtrace+0x0/0xf8) from [<80447500>] (panic +0x48/0xb8)
    [ 2.710000] [<80447500>] (panic+0x48/0xb8) from [<800530bc>] (do_exit+0x698/0 x6bc)
    [ 2.720000] [<800530bc>] (do_exit+0x698/0x6bc) from [<80053360>] (do_group_ex it+0x3c/0xcc)
    [ 2.720000] [<80053360>] (do_group_exit+0x3c/0xcc) from [<80053400>] (__wake_ up_parent+0x0/0x18)

















    Avec le Jumper sur la carte mer du décodeur
    Et cette fois une autre clé usb préalablement formater en FAT32 et brancher sur le port usb du décodeur avec update_ruby de l'image emergency-update-20140305.tar décompresser dessus;
    Ça indique UPDATE sur la face avant du prismcube et une lampre rouge clignotante mais rien d'autre ne ce produit ??

    Un grand merci encore pour votre aide

  6. #5
    Date d'inscription
    novembre 2013
    Messages
    22
    Thanks
    0
    Total, Thanks 25 fois
    Pouvoir de réputation
    0

    Re : Impossible de récupérer mon prismcube même avec tera term ?

    Personne n'à la solution ?

  7. #6
    Date d'inscription
    novembre 2013
    Messages
    22
    Thanks
    0
    Total, Thanks 25 fois
    Pouvoir de réputation
    0

    Re : Impossible de récupérer mon prismcube même avec tera term ?

    Je viens de remarquer cette ligne dans tera term ,


    Libérer la mémoire d'initialisation: 160K / Sbin / init: Erreur lors du chargement des bibliothèques partagées: libkmod.so.2: ne peut pas ouvrir le fichier objet partagé: Aucun fichier ou répertoire


    Cela est elle la cause du problème ?

Règles de messages

  • Vous ne pouvez pas créer de nouvelles discussions
  • Vous ne pouvez pas envoyer des réponses
  • Vous ne pouvez pas envoyer des pièces jointes
  • Vous ne pouvez pas modifier vos messages
  •