guida per il flash dello zgemma h9 combo 4k

How to USB flash the Zgemma H9 Combo using the recovery menu
This is a basic guide to USB flash a local image zip file to the Zgemma H9 Combo.

User will require a USB stick formatted FAT32.

1) Download your chosen image.

2) Transfer the complete zip file to root of the USB stick. Do not unzip the file.

3) Power off the Zgemma H9 Combo and connect the USB stick front USB port behind front flap.

4) Power on the Zgemma H9 Combo, as soon as you power on HOLD DOWN TOP LEFT POWER BUTTON on the remote.

5) Once you're booted into the Multiboot recovery menu screen below select 'Bootmenu' at the bottom and press OK on the remote.


6) On the next screen select 'Flash local image' and press OK on the remote.


7) On the next screen you select the USB stick where your image zip file is located.


8) On the next screen you'll then select the zip file that's on your USB stick that you'd like to flash and press OK on the remote.

9) You'll now select which slot you'd like to flash your image to. Remember which slot you are currently booting from and have setup. Flashing to that slot
WILL REFLASH that slot, you will loose everything you have setup in that slot
. We have setup OpenViX in Slot 1, for this guide we are re-flashing OpenViX in slot 1, OpenATV 6.2 is in slot 2 and we have OpenPLi already flashed to slot 3. Select Slot 1 and press ok on the remote.






10) Once completed you can select which image you'd like to boot into and press ok on the remote.




Questa è una guida di base per il flash local image che ho scritto in base alla procedura da me effettuata (NO RECOVERY) via USB di un file zip di un'immagine locale per Zgemma Questa è una guida di base per il flash local image che ho scritto in base alla procedura da me effettuata (NO RECOVERY) via USB di un file zip di un'immagine locale per Zgemma H9 Combo.

Occorre una chiavetta USB formattata FAT32.

1) Scarica l'immagine scelta.

2) Trasferisci il file zip completo nella root della chiavetta USB. NON DECOMPRIMERE IL FILE

3) Spegnere lo Zgemma H9 Combo e collegare la chiavetta usb alla porta USB anteriore del decoder , dietro lo sportello anteriore SUL D'AVANTI del decoder.

4) Accendere lo Zgemma H9 Combo e appena si accende TENERE PREMUTO IL PULSANTE IN ALTO A SINISTRA del telecomando tasto POWER

5) Una volta avviato nella schermata del menu di ripristino di Multiboot, seleziona 'Bootmenu' nella parte inferiore e premi OK sul telecomando.


6) Nella schermata successiva selezionare 'Flash local image' e premere OK sul telecomando.


7) Nella schermata successiva selezionare la chiavetta USB in cui si trova il file zip dell'immagine (ricordo inserita sulla porta anteriore)


8) Seleziona il file zip che si trova sulla chiavetta USB che desideri flashare e premi OK sul telecomando.


9) Ora dovrai selezionare su quale slot vuoi mostrare la tua immagine. Ricorda in quale slot stai attualmente facendo il boot altrimenti perdi tutti i dati , puoi memorizzare fino a 4 Boot (4 immagini)


10) Una volta completato,e finito il caricamento è possibile selezionare l'immagine in cui si desidera avviare il decoder e premere OK sul telecomando.

Quindi x visualizzare il multiboot accendere il decoder da dietro e simultaneamente premere il tasto power in alto a sx del telecomando e tenerlo premuto ed apparira sul frontalino una scritta rCUY e menu sul televisore con il BOOTMENU' da li scegliere una delle immagini gia' presenti in multiboot sul vostro decoder.

esempio virtuale

Boot1.. openatv
Boot2 LINUX_2 egami
Boot3 LINUX_3 openpli
Boot4 LINUX_4 openvix
ecc ecc
all'interno del Bootmenu e cliccando sulla stessa voce si puo' accedere al menu' successivo


h***s://www.world-of-satellite.com/showthread.php?61483

Flash local Image
Flash online Image
Bootmenu config backup
Bootmenu config restore
Network config.H9 Combo.