Père Nno
04/11/2013, 08h01
Zalut les Zenfants
Trouver sur le net ferais la truduction plus tard
http://linux-tv.com/wp-content/uploads/duo2top1.jpg (http://linux-tv.com/wp-content/uploads/duo2top1.jpg)
VU+ Duo2 contre Solo2
http://linux-tv.com/wp-content/uploads/solo2vsduo2.png (http://linux-tv.com/wp-content/uploads/solo2vsduo2.png)
Vu+ Duo2 est différente du Solo2 quand on regarde les spécifications du tuner.
Le vu+ Duo2 est équipé de 2 slots du tuner. Vous avons donc le choix des tuners que nous souhaitons installer dans ces derniers.
Voici les options actuelles de configuration du tuner possibles
DVB-S2 + DVB-S2
DVB-S2 + DVB-C/T
DVB-S2 Dual + DVB-C/T
DVB-S2 Dual + DVB-S2 Dual
DVB-C/T + DVB-C/T
Ainsi, vous pouvons avoir un maximum de 4 tuners DVB-S2 en utilisant 2 modules double tuner DVB-S2.
Mais bien sûr tuners USB externes sont une option sur le VU + Duo2 trop. USB est actuellement le seul moyen d'avoir des tuners DVB-T2 comme il n'ya pas de module tuner DVB-T2 disponible à partir de VU + encore.
Un peu décevant mais il est soi-disant dans les travaux.
1300 MHz CPU BCM7424 dual-threaded
1GB Flash / 2GB DDR3 DRAM
Option to fit Internal SATA HDD 2.5 or 3″
Dual Card readers
2 x Front display (VFD and LCD)
GigaBit Ethernet
HDMI 1.4
Dolby Digital Plus & DTS 2.0 supported
Dual MPEG2/H.264 Hardware Decoding (HD PiP possible)
On-the-fly hardware transcoding of content into a variety of formats (upport transcoding bit/frame rate change)
Comparaisons techniques entre le Duo² & solo²
Vu+
Duo2
Solo2
Production
Available
Available
Life cycle
2013-
2012-
SoC
BCM7424 (http://www.broadcom.com/products/Satellite/Satellite-Set-Top-Box-Solutions/BCM7424)
BCM7356
CPU type
MIPS
MIPS
CPU (MHz)
2×1300
2×1300
RAM (MiB)
2048
1024
Flash (MiB)
1024
256
Default OS
Enigma2
Enigma2
DVB
2 × S2/C/T
2 × S2
HDTV
Yes
Yes
3D TV
Yes
Yes
PiP
Yes/HD
Yes/HD
Common Interface
2
1
Smart card
2
2
USB
3 x 2.0
3 x 2.0
RS232
Yes
Yes
LAN (Mbit/s)
1000
1000
HDD
2.5/3.5 in
2.5 in
ATA
SATA
SATA
eSATA
Yes
No
SCART
1
1
HDMI
1
1
Display
VFD+LCD
VFD
Transcoding
Hardware
Software
Other connectors
1 x YPrPb
Dimensions, WxHxD (mm)
380 x 60 x 290
280 x 50 x 200
Par rapport à la Solo2 nous voyons de nombreuses améliorations ou des options supplémentaires si vous le souhaitez. Bien sûr, nous avons maintenant les tuners enfichables et également une bonne croissance sur les spécifications de la mémoire et le WiFi est construit po Le 3.2 Ajout de l'affichage "TFT LCD 262.000 couleurs du panneau avant définit également le Duo2 part.
Il est également intéressant de noter que le Duo2 a consacré matériel dans la boîte de transcodage où le Solo2 est un logiciel basé. Sur le Duo2 vous pouvez modifier le bit / trame taux de transcodage alors qu'il était fixé sur le Solo2.
Du côté de la connexion des choses le Duo2 propose composant sur vidéo et e-Sata. D'Vu + Duo2 vous pouvez aussi mettre à la fois un disque dur 2.5 "et 3.5", alors que seulement 2,5 a été pris en charge sur le Solo2.
La nouvelle télécommande Duo2 ya une autre différence entre les deux, mais pour le moment nous avons encore à essayer ce qu'il y aura un retard sur ceux-ci.
Vu+ Duo2 design and connections
http://linux-tv.com/wp-content/uploads/vuduo2_front-625x133.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_front.jpg)The VU+ Duo2 is similar to the VU+ Ultimo in stylish black of course. The front though has something which the Ultimo2 has not and that is the 3.2” TFT LCD 262,000 colour front panel display on the left. In the center we have the more traditionel VFD display. There are no controls on the receiver for volume or channel change only a power button which is hidden behind the front flap.http://linux-tv.com/wp-content/uploads/vuduo2_cardreaders-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_cardreaders.jpg)If we flip down the front flap 2 internal card readers are revealed along with 2 common interface slots. Add to that a front USB connector which is very useful for putting a new Image on the box or for a simple file transfer without having to plug in the USB device on the back.http://linux-tv.com/wp-content/uploads/vuduo2_rear1-625x128.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_rear1.jpg)On the back we find these connections:
2 x Tuner slots
Composite video and analogue audio out
Component video out
1x scart
HDMI
GigaBit Ethernet port
2 x USB
1 x e-Sata
Serial RS-232 port
Optical digital audio out
Power connector and switch
As you can see on the picture of the Duo2 rear there is a cover beside the 2 tuner modules this is for fitting an optional external WiFi antenna and not a third tuner module.http://linux-tv.com/wp-content/uploads/vuduo2_insidetuners-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidetuners.jpg)http://linux-tv.com/wp-content/uploads/vuduo2_reartuners-625x408.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_reartuners.jpg)Our review unit was equipped with 1 Dual DVB-S2 tuner and 1 DVB-C/T tuner.http://linux-tv.com/wp-content/uploads/vuduo2_insidehfan-625x309.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidehfan.jpg)As you can see there is a fan mounted at the back. It is not a noisy fan so should not be a problem and the fan has an automatic temperature sensor based FAN speed control so it will not make more noise than needed to keep things cool.http://linux-tv.com/wp-content/uploads/vuduo2_boxcontents-625x277.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_boxcontents.jpg)The VU+ Duo2 is delivered with:
Power Supply
Remote with batteries included
1 x HDMI cable
Setup guide in English/German
Cables, screws, fittings for internal PVR
Loop Through cable
The Duo2 Remote
http://linux-tv.com/wp-content/uploads/vuduo2_remote-625x173.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote.jpg)
http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteries-625x212.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteries.jpg)
The Duo2 remote was a bit delayed but we now have it. The new Vu+ Duo2 remote requires 3 x AAA batteries which is one more than usual on remotes. It has a curved end at the back of the remote where the batteries are placed.
It looks a bit more high end than the one that is delivered with the Vu+ Solo2. It also feels a bit more heavy than most remotes but and in general it feels fine in the hand but perhaps with a feeling that it could slide out of your hand. Perhaps some kind of rubber material on the back would have helped.
http://linux-tv.com/wp-content/uploads/vuduo2_remote_navigation-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_navigation.jpg)
The main navigation buttons + the menu/channel/volume buttons are in silver which makes them stand out a bit.
http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteryinfo-625x318.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteryinfo.jpg)
At the bottom there is a low battery indicator. The PVR buttons are located at the top of the remote and there are dedicated buttons for what you would expect except perhaps one for subtitles.
The range of the remote seems fine but it does seem a bit more picky than the old Duo. You have to point more precisely at the receiver with the Duo2.
Installation and Image support
The Vu+ Duo2 is of course delivered with software already pre-installed but most likely you will want to install a third party image.Vu+ is probably one of the most widely supported receivers so you will have no trouble finding images from the likes of Blackhole, Vix, VTi and many more at least not after a little while. Check our Vu+ information box for links. You find this to the right at the top of the review.The BlackHole Image for the Duo2 was released just a few days before we did this review.
Installing a new Image is easy on the VU+ Duo2 http://linux-tv.com/wp-content/uploads/usbupdate.png (http://linux-tv.com/wp-content/uploads/usbupdate.png)
Download the VU+ Duo2 image you want to install on your PC.
Unzip to a USB stick
Turn off the VU+ Duo2 on the back
Insert the USB stick on the front of the Duo2
Turn on the VU+ Duo2
Follow the messages on the front display of the Duo2.
Press the power button to install
The Duo2 installs the image from the usb and reboots.
Inside the VU+ Duo2
http://linux-tv.com/wp-content/uploads/vuduo2_insidehdd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidehdd.jpg)
The Vu+ Duo2 looks very well built everything is pretty tidy inside and nicely separated.
http://linux-tv.com/wp-content/uploads/vuduo2_insidepower-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidepower.jpg)
Vu+ is using an internal power supply for the Vu+ Duo2 which makes sense since there is plenty of room inside of this receiver.
The HDD mounting tray does no have the raised guides on the mount points as was the case on the Solo2 but it is still pretty easy to work with.Installing a hard drive is quite easy on the VU+ Duo2. All the necessary screws and cables are included. The hard drive can be a 2.5 or 3.5″ sata hard drive.
The 3.2” TFT LCD display
http://linux-tv.com/wp-content/uploads/vuduo2_lcdfront-625x153.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_lcdfront.jpg)
We must start our usage part of this review with the most noticeable new thing on this receiver namely the LCD display.
http://linux-tv.com/wp-content/uploads/vuduo2_piconlcd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_piconlcd.jpg)
You can customize the look of the display by using the LCD4linux plugin. You get to this by pressing the green button on the remote.
There are a lot of options and thankfully setting up the layout i very visual so you can see how it looks like inside the plugin on screen menu while you customize. If is possible to use picons in the LCD display. Do not forget to adjust your path to the picons folder if needed.
http://linux-tv.com/wp-content/uploads/weather_lcd4linux.png (http://linux-tv.com/wp-content/uploads/weather_lcd4linux.png)
You can spend a lot of time customizing the display and include weather information, time and program info and much more. There are different LCD modes for on, idle and media playback.
The LCD may be too small for many from a distance if you add to much information to it. Channel logos and the time works fine also from a distance. The VFD display is similar to the one on the Ultimo but actually it feels a bit fuzzy when you have the clear LCD beside it.
If Vu+ wanted to go ultra high end they should have put one big LCD panel on the whole front instead of having both.
All in all we do like the LCD and with the plugin it is more easy to customize than the VFD.
Daily use
Booting speed
As we expected the Vu+ Duo2 is really fast. Booting a full feature Image including Hbb-TV support and everything is done in 33 seconds.Boot leaderboard
Receiver
Boot (secs)
Vu+ Duo2 (http://linux-tv.com/receiver/vu-duo2-review/)
33
Vu+ Solo2 (http://linux-tv.com/receiver/vu-solo2-review/)
35
GigaBlue Quad HD (http://linux-tv.com/receiver/gigablue-hd-quad-review/)
47
VU+ Ultimo (http://linux-tv.com/receiver/vu-ultimo-review/)
49
VU+ Uno (http://linux-tv.com/receiver/vu-uno-review/)
54
Clarke-Tech ET-9000 (http://linux-tv.com/receiver/xtrend-et-9000-review/)
63
IQON IOS 100 HD (http://linux-tv.com/receiver/iqon-ios-100-hd/)
65
Venton UNiBOX HD2 (http://linux-tv.com/receiver/venton-unibox-hd2-review/)
65
Dreambox 7020 HD (http://linux-tv.com/receiver/dm7020-hd-review/)
71
Venton UNiBOX HD1 (http://linux-tv.com/receiver/venton-unibox-hd1-review/)
72
VU+ Duo (http://linux-tv.com/receiver/vu-duo-review/)
80
http://linux-tv.com/wp-content/uploads/vusolo2_bh_speedup-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_speedup.jpg)The BlackHole image even offers to make the boot even faster with the BlackHole SpeedUp feature. This function allows you to enable / disable various plugins and features that are included by default in the image, so you can disable any plugins you do not wish to use, and this will in turn speed up the boot (and restart) time of your Vu+ receiver.Press Blue button on the remote control and then Blue button again and select BlackHole SpeedUp, select which options you want to disable and then press Red button to save and reboot the receiver.In our experience you can shave a few seconds by using this but it is plenty fast even without.Picture/tuner quality, zapping speed and Picture in Picture
We cannot complain about the tuner sensitivity of the DVB-S2 tuners and the picture quality is great. You can set the video output up to 1080p 50/60Hz. If you need 1080p24, 1080p25 or 1080p30 you can do this with the auto resolution plugin.http://linux-tv.com/wp-content/uploads/vuduo2_tvzap-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_tvzap.jpg)Channel zapping is really fast and you can of course play around with the on screen graphics look by downloading and changing skins.One thing is still a bit slow and that is the channel searching so you might want to hunt down some settings. We have tried both satellite and Cable TV scanning and both found the channels just fine. There is also a blind scan option on the Duo2.
http://linux-tv.com/wp-content/uploads/vusolo2_bh_piphd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_piphd.jpg)
The VU+ Duo2 offers Picture in Picture mode and even support full HD channels in this mode. This is excellent and what we expect from a second generation device like this. A dedicated PiP button on the remote would have been great but that is sadly missing. On Black Hole image you get to this by long press blue and the blue again.PVR and Multimedia playback
With dual tuners or perhaps even quad DVB-S2 tuners you will be able to record a lot at once. All recordings are of course saved into .ts files which are easily transferred over the high speed Ethernet if you want to edit them on your computer.The Vu+ Duo2 serves well as a media player, playing video, music stored on the box hard drive or your home network. Do not expect every file format out there to be supported. But common mp3, flac, avi and mkv files are handled pretty well. Hbb-TV and Internet Browser
http://linux-tv.com/wp-content/uploads/vuduo2_hbbtv-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_hbbtv.jpg)
Hbb-TV is working well on a fast receiver like this.http://linux-tv.com/wp-content/uploads/vusolo2_bh_webbrowser-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_webbrowser.jpg)Using the Vu+ Duo2 you are also able to browse the Internet with the integrated browser. On the BlackHole Image you do this via the plugins panel (green button), activate the Opera browser and enter the URL using the remote control. Using the browser via the remote control is somewhat a challenge though.Improved Transcoding feature
http://linux-tv.com/wp-content/uploads/vuduo2_transcoding.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_transcoding.jpg)
On of the interesting new features on the Vu+ Duo2 is the on-the-fly transcoding of content to other devices. The transcoding gives you the opportunity to stream tv from the Duo2 to your pc at the office or your tablet or smartphone. It works both inside and outside of the home network, therefore it also works over the internet, if you have the correct ports open in your router. It also works via 3g if your connection is good enough.
The transcoding was also a feature on the Solo2 but it was software based and the quality was fixed at a pretty low bitrate on the Vu+ Duo2 there is hardware transcoding with more control over the bit/framerate.
Check our detailed guide on setting remote streaming up here (http://linux-tv.com/vu-solo2-transcoding-router-setup/).
Vu+ Duo2 Review Conclusion
The Vu+ Duo2 was definitely worth the wait. It really stands out from the the rest of the crowded Enigma2 based receiver market.
The Duo2 has more options than the Solo2 with its pluggable tuner slots and it just feels more high end.
They Vu+ Duo2 is the fastest Enigma2 based receiver we have reviewed as of yet and that comes as no surprise if we look at the strong specs of this receiver. The transcoding feature is better on the Duo2 than on the Solo2 and while we are not complete sold on the front VFD display it is not a big negative and the LCD display looks nice and clear and is pretty easy to customize once you have experimented for a while.
Where could the Duo2 be even better? Well we do have a quad tuner slot receiver on the market so 2 tuner slots is perhaps a bit modest. Thankfully there are Dual DVB-S2 tuner modules but if you are on DVB-C/T you do not have the quad tuner option. DVB-T2 option also would have been a bonus.
Trouver sur le net ferais la truduction plus tard
http://linux-tv.com/wp-content/uploads/duo2top1.jpg (http://linux-tv.com/wp-content/uploads/duo2top1.jpg)
VU+ Duo2 contre Solo2
http://linux-tv.com/wp-content/uploads/solo2vsduo2.png (http://linux-tv.com/wp-content/uploads/solo2vsduo2.png)
Vu+ Duo2 est différente du Solo2 quand on regarde les spécifications du tuner.
Le vu+ Duo2 est équipé de 2 slots du tuner. Vous avons donc le choix des tuners que nous souhaitons installer dans ces derniers.
Voici les options actuelles de configuration du tuner possibles
DVB-S2 + DVB-S2
DVB-S2 + DVB-C/T
DVB-S2 Dual + DVB-C/T
DVB-S2 Dual + DVB-S2 Dual
DVB-C/T + DVB-C/T
Ainsi, vous pouvons avoir un maximum de 4 tuners DVB-S2 en utilisant 2 modules double tuner DVB-S2.
Mais bien sûr tuners USB externes sont une option sur le VU + Duo2 trop. USB est actuellement le seul moyen d'avoir des tuners DVB-T2 comme il n'ya pas de module tuner DVB-T2 disponible à partir de VU + encore.
Un peu décevant mais il est soi-disant dans les travaux.
1300 MHz CPU BCM7424 dual-threaded
1GB Flash / 2GB DDR3 DRAM
Option to fit Internal SATA HDD 2.5 or 3″
Dual Card readers
2 x Front display (VFD and LCD)
GigaBit Ethernet
HDMI 1.4
Dolby Digital Plus & DTS 2.0 supported
Dual MPEG2/H.264 Hardware Decoding (HD PiP possible)
On-the-fly hardware transcoding of content into a variety of formats (upport transcoding bit/frame rate change)
Comparaisons techniques entre le Duo² & solo²
Vu+
Duo2
Solo2
Production
Available
Available
Life cycle
2013-
2012-
SoC
BCM7424 (http://www.broadcom.com/products/Satellite/Satellite-Set-Top-Box-Solutions/BCM7424)
BCM7356
CPU type
MIPS
MIPS
CPU (MHz)
2×1300
2×1300
RAM (MiB)
2048
1024
Flash (MiB)
1024
256
Default OS
Enigma2
Enigma2
DVB
2 × S2/C/T
2 × S2
HDTV
Yes
Yes
3D TV
Yes
Yes
PiP
Yes/HD
Yes/HD
Common Interface
2
1
Smart card
2
2
USB
3 x 2.0
3 x 2.0
RS232
Yes
Yes
LAN (Mbit/s)
1000
1000
HDD
2.5/3.5 in
2.5 in
ATA
SATA
SATA
eSATA
Yes
No
SCART
1
1
HDMI
1
1
Display
VFD+LCD
VFD
Transcoding
Hardware
Software
Other connectors
1 x YPrPb
Dimensions, WxHxD (mm)
380 x 60 x 290
280 x 50 x 200
Par rapport à la Solo2 nous voyons de nombreuses améliorations ou des options supplémentaires si vous le souhaitez. Bien sûr, nous avons maintenant les tuners enfichables et également une bonne croissance sur les spécifications de la mémoire et le WiFi est construit po Le 3.2 Ajout de l'affichage "TFT LCD 262.000 couleurs du panneau avant définit également le Duo2 part.
Il est également intéressant de noter que le Duo2 a consacré matériel dans la boîte de transcodage où le Solo2 est un logiciel basé. Sur le Duo2 vous pouvez modifier le bit / trame taux de transcodage alors qu'il était fixé sur le Solo2.
Du côté de la connexion des choses le Duo2 propose composant sur vidéo et e-Sata. D'Vu + Duo2 vous pouvez aussi mettre à la fois un disque dur 2.5 "et 3.5", alors que seulement 2,5 a été pris en charge sur le Solo2.
La nouvelle télécommande Duo2 ya une autre différence entre les deux, mais pour le moment nous avons encore à essayer ce qu'il y aura un retard sur ceux-ci.
Vu+ Duo2 design and connections
http://linux-tv.com/wp-content/uploads/vuduo2_front-625x133.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_front.jpg)The VU+ Duo2 is similar to the VU+ Ultimo in stylish black of course. The front though has something which the Ultimo2 has not and that is the 3.2” TFT LCD 262,000 colour front panel display on the left. In the center we have the more traditionel VFD display. There are no controls on the receiver for volume or channel change only a power button which is hidden behind the front flap.http://linux-tv.com/wp-content/uploads/vuduo2_cardreaders-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_cardreaders.jpg)If we flip down the front flap 2 internal card readers are revealed along with 2 common interface slots. Add to that a front USB connector which is very useful for putting a new Image on the box or for a simple file transfer without having to plug in the USB device on the back.http://linux-tv.com/wp-content/uploads/vuduo2_rear1-625x128.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_rear1.jpg)On the back we find these connections:
2 x Tuner slots
Composite video and analogue audio out
Component video out
1x scart
HDMI
GigaBit Ethernet port
2 x USB
1 x e-Sata
Serial RS-232 port
Optical digital audio out
Power connector and switch
As you can see on the picture of the Duo2 rear there is a cover beside the 2 tuner modules this is for fitting an optional external WiFi antenna and not a third tuner module.http://linux-tv.com/wp-content/uploads/vuduo2_insidetuners-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidetuners.jpg)http://linux-tv.com/wp-content/uploads/vuduo2_reartuners-625x408.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_reartuners.jpg)Our review unit was equipped with 1 Dual DVB-S2 tuner and 1 DVB-C/T tuner.http://linux-tv.com/wp-content/uploads/vuduo2_insidehfan-625x309.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidehfan.jpg)As you can see there is a fan mounted at the back. It is not a noisy fan so should not be a problem and the fan has an automatic temperature sensor based FAN speed control so it will not make more noise than needed to keep things cool.http://linux-tv.com/wp-content/uploads/vuduo2_boxcontents-625x277.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_boxcontents.jpg)The VU+ Duo2 is delivered with:
Power Supply
Remote with batteries included
1 x HDMI cable
Setup guide in English/German
Cables, screws, fittings for internal PVR
Loop Through cable
The Duo2 Remote
http://linux-tv.com/wp-content/uploads/vuduo2_remote-625x173.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote.jpg)
http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteries-625x212.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteries.jpg)
The Duo2 remote was a bit delayed but we now have it. The new Vu+ Duo2 remote requires 3 x AAA batteries which is one more than usual on remotes. It has a curved end at the back of the remote where the batteries are placed.
It looks a bit more high end than the one that is delivered with the Vu+ Solo2. It also feels a bit more heavy than most remotes but and in general it feels fine in the hand but perhaps with a feeling that it could slide out of your hand. Perhaps some kind of rubber material on the back would have helped.
http://linux-tv.com/wp-content/uploads/vuduo2_remote_navigation-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_navigation.jpg)
The main navigation buttons + the menu/channel/volume buttons are in silver which makes them stand out a bit.
http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteryinfo-625x318.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_remote_batteryinfo.jpg)
At the bottom there is a low battery indicator. The PVR buttons are located at the top of the remote and there are dedicated buttons for what you would expect except perhaps one for subtitles.
The range of the remote seems fine but it does seem a bit more picky than the old Duo. You have to point more precisely at the receiver with the Duo2.
Installation and Image support
The Vu+ Duo2 is of course delivered with software already pre-installed but most likely you will want to install a third party image.Vu+ is probably one of the most widely supported receivers so you will have no trouble finding images from the likes of Blackhole, Vix, VTi and many more at least not after a little while. Check our Vu+ information box for links. You find this to the right at the top of the review.The BlackHole Image for the Duo2 was released just a few days before we did this review.
Installing a new Image is easy on the VU+ Duo2 http://linux-tv.com/wp-content/uploads/usbupdate.png (http://linux-tv.com/wp-content/uploads/usbupdate.png)
Download the VU+ Duo2 image you want to install on your PC.
Unzip to a USB stick
Turn off the VU+ Duo2 on the back
Insert the USB stick on the front of the Duo2
Turn on the VU+ Duo2
Follow the messages on the front display of the Duo2.
Press the power button to install
The Duo2 installs the image from the usb and reboots.
Inside the VU+ Duo2
http://linux-tv.com/wp-content/uploads/vuduo2_insidehdd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidehdd.jpg)
The Vu+ Duo2 looks very well built everything is pretty tidy inside and nicely separated.
http://linux-tv.com/wp-content/uploads/vuduo2_insidepower-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_insidepower.jpg)
Vu+ is using an internal power supply for the Vu+ Duo2 which makes sense since there is plenty of room inside of this receiver.
The HDD mounting tray does no have the raised guides on the mount points as was the case on the Solo2 but it is still pretty easy to work with.Installing a hard drive is quite easy on the VU+ Duo2. All the necessary screws and cables are included. The hard drive can be a 2.5 or 3.5″ sata hard drive.
The 3.2” TFT LCD display
http://linux-tv.com/wp-content/uploads/vuduo2_lcdfront-625x153.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_lcdfront.jpg)
We must start our usage part of this review with the most noticeable new thing on this receiver namely the LCD display.
http://linux-tv.com/wp-content/uploads/vuduo2_piconlcd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_piconlcd.jpg)
You can customize the look of the display by using the LCD4linux plugin. You get to this by pressing the green button on the remote.
There are a lot of options and thankfully setting up the layout i very visual so you can see how it looks like inside the plugin on screen menu while you customize. If is possible to use picons in the LCD display. Do not forget to adjust your path to the picons folder if needed.
http://linux-tv.com/wp-content/uploads/weather_lcd4linux.png (http://linux-tv.com/wp-content/uploads/weather_lcd4linux.png)
You can spend a lot of time customizing the display and include weather information, time and program info and much more. There are different LCD modes for on, idle and media playback.
The LCD may be too small for many from a distance if you add to much information to it. Channel logos and the time works fine also from a distance. The VFD display is similar to the one on the Ultimo but actually it feels a bit fuzzy when you have the clear LCD beside it.
If Vu+ wanted to go ultra high end they should have put one big LCD panel on the whole front instead of having both.
All in all we do like the LCD and with the plugin it is more easy to customize than the VFD.
Daily use
Booting speed
As we expected the Vu+ Duo2 is really fast. Booting a full feature Image including Hbb-TV support and everything is done in 33 seconds.Boot leaderboard
Receiver
Boot (secs)
Vu+ Duo2 (http://linux-tv.com/receiver/vu-duo2-review/)
33
Vu+ Solo2 (http://linux-tv.com/receiver/vu-solo2-review/)
35
GigaBlue Quad HD (http://linux-tv.com/receiver/gigablue-hd-quad-review/)
47
VU+ Ultimo (http://linux-tv.com/receiver/vu-ultimo-review/)
49
VU+ Uno (http://linux-tv.com/receiver/vu-uno-review/)
54
Clarke-Tech ET-9000 (http://linux-tv.com/receiver/xtrend-et-9000-review/)
63
IQON IOS 100 HD (http://linux-tv.com/receiver/iqon-ios-100-hd/)
65
Venton UNiBOX HD2 (http://linux-tv.com/receiver/venton-unibox-hd2-review/)
65
Dreambox 7020 HD (http://linux-tv.com/receiver/dm7020-hd-review/)
71
Venton UNiBOX HD1 (http://linux-tv.com/receiver/venton-unibox-hd1-review/)
72
VU+ Duo (http://linux-tv.com/receiver/vu-duo-review/)
80
http://linux-tv.com/wp-content/uploads/vusolo2_bh_speedup-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_speedup.jpg)The BlackHole image even offers to make the boot even faster with the BlackHole SpeedUp feature. This function allows you to enable / disable various plugins and features that are included by default in the image, so you can disable any plugins you do not wish to use, and this will in turn speed up the boot (and restart) time of your Vu+ receiver.Press Blue button on the remote control and then Blue button again and select BlackHole SpeedUp, select which options you want to disable and then press Red button to save and reboot the receiver.In our experience you can shave a few seconds by using this but it is plenty fast even without.Picture/tuner quality, zapping speed and Picture in Picture
We cannot complain about the tuner sensitivity of the DVB-S2 tuners and the picture quality is great. You can set the video output up to 1080p 50/60Hz. If you need 1080p24, 1080p25 or 1080p30 you can do this with the auto resolution plugin.http://linux-tv.com/wp-content/uploads/vuduo2_tvzap-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_tvzap.jpg)Channel zapping is really fast and you can of course play around with the on screen graphics look by downloading and changing skins.One thing is still a bit slow and that is the channel searching so you might want to hunt down some settings. We have tried both satellite and Cable TV scanning and both found the channels just fine. There is also a blind scan option on the Duo2.
http://linux-tv.com/wp-content/uploads/vusolo2_bh_piphd-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_piphd.jpg)
The VU+ Duo2 offers Picture in Picture mode and even support full HD channels in this mode. This is excellent and what we expect from a second generation device like this. A dedicated PiP button on the remote would have been great but that is sadly missing. On Black Hole image you get to this by long press blue and the blue again.PVR and Multimedia playback
With dual tuners or perhaps even quad DVB-S2 tuners you will be able to record a lot at once. All recordings are of course saved into .ts files which are easily transferred over the high speed Ethernet if you want to edit them on your computer.The Vu+ Duo2 serves well as a media player, playing video, music stored on the box hard drive or your home network. Do not expect every file format out there to be supported. But common mp3, flac, avi and mkv files are handled pretty well. Hbb-TV and Internet Browser
http://linux-tv.com/wp-content/uploads/vuduo2_hbbtv-625x351.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_hbbtv.jpg)
Hbb-TV is working well on a fast receiver like this.http://linux-tv.com/wp-content/uploads/vusolo2_bh_webbrowser-625x351.jpg (http://linux-tv.com/wp-content/uploads/vusolo2_bh_webbrowser.jpg)Using the Vu+ Duo2 you are also able to browse the Internet with the integrated browser. On the BlackHole Image you do this via the plugins panel (green button), activate the Opera browser and enter the URL using the remote control. Using the browser via the remote control is somewhat a challenge though.Improved Transcoding feature
http://linux-tv.com/wp-content/uploads/vuduo2_transcoding.jpg (http://linux-tv.com/wp-content/uploads/vuduo2_transcoding.jpg)
On of the interesting new features on the Vu+ Duo2 is the on-the-fly transcoding of content to other devices. The transcoding gives you the opportunity to stream tv from the Duo2 to your pc at the office or your tablet or smartphone. It works both inside and outside of the home network, therefore it also works over the internet, if you have the correct ports open in your router. It also works via 3g if your connection is good enough.
The transcoding was also a feature on the Solo2 but it was software based and the quality was fixed at a pretty low bitrate on the Vu+ Duo2 there is hardware transcoding with more control over the bit/framerate.
Check our detailed guide on setting remote streaming up here (http://linux-tv.com/vu-solo2-transcoding-router-setup/).
Vu+ Duo2 Review Conclusion
The Vu+ Duo2 was definitely worth the wait. It really stands out from the the rest of the crowded Enigma2 based receiver market.
The Duo2 has more options than the Solo2 with its pluggable tuner slots and it just feels more high end.
They Vu+ Duo2 is the fastest Enigma2 based receiver we have reviewed as of yet and that comes as no surprise if we look at the strong specs of this receiver. The transcoding feature is better on the Duo2 than on the Solo2 and while we are not complete sold on the front VFD display it is not a big negative and the LCD display looks nice and clear and is pretty easy to customize once you have experimented for a while.
Where could the Duo2 be even better? Well we do have a quad tuner slot receiver on the market so 2 tuner slots is perhaps a bit modest. Thankfully there are Dual DVB-S2 tuner modules but if you are on DVB-C/T you do not have the quad tuner option. DVB-T2 option also would have been a bonus.